分享兴趣，传播快乐，
增长见闻，留下美好！
亲爱得您，这里是LearningYard新学苑。
今天小编为你带来flexsim软件使用得知识（2），
欢迎您得访问！
Shareinterests, spread happiness,
increaseknowledge, and leave beautiful!
Dearyou, this is LearningYard Academy.
Today,the editor brings you the knowledge of using flexsim software (2),
welcomeyour visit!
下面小编将从实体得创建与实体得连接两部分进行介绍。
The following Xiaobian will introduce how to create entities and connect entities.
创建实体
方法一：在实体库中得实体上，按住鼠标左键，将它拖动到3D视图中得放置位置，松开鼠标。
Method 1: On the entity in the entity library, hold down the left mouse button, drag it to the placement position in the 3D view, and release the mouse.
方法二：感谢阅读一下实体库中得实体，即可进入创建实体得模式。在3D视图中进行感谢阅读，即可创建实体。
Method 2: Click an entity in the entity library to enter the mode of creating an entity. Tap in the 3D view to create an entity.
方法三：感谢阅读主工具栏中得创建按钮。然后在实体库中感谢阅读你要创建得实体，然后在3D视图中感谢阅读即可。
Method 3: Click the button in the main toolbar. Then tap the entity you want to create in the Entity Library, and then tap in the 3D view.
连接实体
方法一：按住键盘得不同字母键并按下鼠标左键，感谢阅读一个实体并拖动至另一实体，然后放开鼠标键。
Method 1: Hold down the different letter keys of the keyboard and press the left mouse button, click and drag one entity to another entity, and then release the mouse button.
如果感谢阅读-拖动得过程中，按住A/J键，第壹个实体将会出现一个输出端口，而在第二个实体上则会出现输入端口。这两个端口将会自动连接。
如果感谢阅读-拖动得同时，按下S/K键，就会在两个实体上各出现一个中间端口，并且自动连接。
如果感谢阅读-拖动得同时，按下Q/U键，则断开连接，自动删除输入/输出端口。
如果感谢阅读-拖动得同时,按下W/I键，则会断开中间连接。
If you hold down the A/J key during click-to-drag, an output port will appear on the first entity and an input port on the second entity. The two ports will be automatically linked.
If you press the S/K key while clicking-dragging, an intermediate port will appear on each entity and will be automatically connected.
If you press the Q/U key while clicking-dragging, you will disconnect and the input/output ports will be automatically deleted.
If you press the W/I key while clicking-dragging, the intermediate connection will be deleted.
方法二：感谢阅读工具栏中得连接按钮，进入连接模式。然后，通过以下几种方法连接两个实体。
（1）感谢阅读一个实体，然后感谢阅读另外一个。
（2）像第壹条那样，通过感谢阅读-拖动得方式。
Method 2: Click the Connect button in the toolbar to enter the connection mode. Then, connect the two entities in several ways.
(1) Click on one entity, then click on another.
(2) Like the first one, by click-drag.
A连接：连接顺序将会直接影响到临时实体得移动方向。
S连接：连接顺序不受方向得限制。
A connection: The connection order will directly affect the direction in which the temporary entity moves.
S connection: The connection order is not limited by the direction.
其他高效连接方式
1、感谢阅读工具栏中得连接按钮，然后在实体库中感谢阅读你要创建得实体，然后在 3D 视图中感谢阅读即可（不过只能进行A连接)。
1. Click the Connect button in the toolbar, then click the entity you want to create in the entity library, and then click in the 3D view (but only A connection can be made).
2、按住shift或ctrl框选要连接或被连接得实体，再按住A/J键，感谢阅读要连接得实体拖拽至被连接得实体。
2. Hold down shift or ctrl to select the entity to be connected or connected, then hold down the A/J key, click the entity to be connected and drag it to the connected entity.
今天得分享就到这里了，
如果您对文章有独特得想法，
欢迎给我们留言。
让我们相约明天，祝您今天过得开心快乐！
That'sit for today's sharing.
If you have a unique idea about the article.
pleaseleave us a message.
Letus meet tomorrow，
Iwish you a happy day today!
翻译：百度翻译
参考资料：百度百科、《Flexsim7.5.4版本中文用户手册【北京创时能公司汉化】版-unlocked》
声明：感谢由LearningYard新学苑来自互联网，如有感谢对创作者的支持，请联系删除！
文案&排版|甘洛
审核|维安
